Tips On How To Extend Smok Pen Recharge Time


Tips On How To Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was created by two guys in California. They wished to create a cool writing instrument that looked like a genuine pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the market by storm.

The Smok Pen has a built quality that’s just great. I came across that even though it is an electronic pen the construction is just as good as the pens that I’ve reviewed. The reason being of how they made the most notable cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the form of the coils and the way that they are built. Generally the coil on a Smok Pen is bigger than on other pens. I believe that they did this deliberately, to make the pen feel bigger.

Invest the a glance at a Smok Pen, you will observe that the body of the pen is round and not smooth like other pens. On the back of the pen there is a little tab that houses the coil. When you press on the tab it is simple to turn the heating element on and off. I must say i liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.

To utilize the Smok Pen it is advisable to keep carefully the heat button pressed. Once the button is pressed, the heating element will start to warm up. Once it gets to the appropriate temperature you can turn off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.

When you put your Smok Pen in to the tank you will notice a indicator light come on. The indicator light will remain green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids in to the coil heads.

After you have completed this step, you should always check to see should you be at the proper temperature for the coils to fire. If not then you should turn the energy off and try again. When you are still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the next two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.

Before you go any further you should remove the battery from your own pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You should loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.

Once you have placed the sub-ohm tank into the pen you should then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the energy and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you first put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set then you should follow the on screen instructions.

After the Smok Pen has already reached the temperature that it requires to reach you need to then connect both wires to the negative and JUUL Pods positive on the positive post on the Smok unit. You should then connect the other end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to the bottom of the Smok’s on / off switch.

After all the components have been placed into the pen, you should turn the power on. Following the first test run, you have to be able to start to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you should take away the battery from the pen and replace it with a fresh one. For your convenience there is also a green light that can be pressed so as to confirm the battery charging status. When you have done these things and you also do not see the green light indicating charging, you should replace the battery.

Posted in Uncategorized